MATLAB CONTROL SYSTEM TOOLBOX 9 Guia do Utilizador Página 125
- Página / 649
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Continuous/Discrete Conversions of LTI Models
3-21
The signal is then fed to the continuous system , and the resulting
output is sampled every seconds to produce .
Conversely, given a discrete system , the
d2c conversion produces a
continuous system whose ZOH discretization coincides with . This
inverse operation has the following limitations:
•
d2c cannotoperate on LTImodels with poles at whenthe ZOH is used.
• Negative real poles in t he domain are mapped t o pairs of complex poles in
the domain. As a result, the
d2c conversion of a discrete system with
negative real poles produces a continuous system with higher order.
The next example illustrates the behavior of
d2c with real negative poles.
Consider the following discrete-time ZPK model.
hd = zpk([],–0.5,1,0.1)
Zero/pole/gain:
1
-------
(z+0.5)
Sampling time: 0.1
Use d2c to convert this model to continuous-time
hc = d2c(hd)
and you get a second-order model.
Zero/pole/gain:
4.621 (s+149.3)
---------------------
(s^2 + 13.86s + 1035)
Discretize the model again
c2d(hc,0.1)
ut
()
uk
[]
,
=
kT
s
tk1
+()
T
s
≤≤
ut
()
Hs
()
yt
()
T
s
yk
[]
H
d
z
()
Hs
()
H
d
z
()
z 0
=
z
s
- Control System 1
- How to Contact The MathWorks: 2
- Control Design Tools 10
- The Root Locus Design GUI 11
- Design Case Studies 12
- Reliable Computations 13
- Reference 13
- Contents 14
- Preface 16
- Installation 17
- Typographic Conventions 19
- Quick Start 21
- 1 Quick Start 22
- LTI Models 23
- Model Conversion 25
- LTI Properties 27
- System Interconnections 39
- Other Uses of FRD Models 47
- LTI Objects 47
- Precedence Rules 49
- Creating LTI Models 53
- Pure Gains 55
- MIMO Zero-Pole-Gain Models 57
- Direct Property Referencing 77
- Automatic Conversion 87
- Time Delays 89
- Distillation Column Example 91
- 2 LTI Models 100
- References 103
- Operations on LTI Models 105
- 3 Operations on LTI Models 106
- Resizing LTI Systems 113
- Arithmetic Operations 115
- Multiplication 117
- Concatenation of LTI Models 121
- Matched Poles and Zeros 127
- Arrays of LTI Models 133
- 4 Arrays of LTI Models 134
- Introduction 135
- The Concept of an LTI Array 137
- Building LTI Arrays 145
- Indexing Into LTI Arrays 153
- Operations on LTI Arrays 157
- Dimension Requirements 159
- Model Analysis Tools 163
- 5 Model Analysis Tools 164
- General Model Characteristics 165
- Model Dynamics 167
- State-Space Realizations 169
- Time and Frequency Response 171
- Frequency Response 173
- Customizing the Plot Display 179
- The LTI Viewer 183
- 6 The LTI Viewer 184
- File menu has 189
- Tools menu items 189
- 1 Click on the marker 191
- Importing Models 193
- The LTI Viewer Menus 197
- Interactive Help 199
- The Right-Click Menus 201
- Characteristics or the 203
- The Axes Grouping Submenu 205
- Axes Grouping 205
- Shift key while 209
- Arrays pull-down tab 213
- Index into Dimensions 217
- The LTI Viewer Tools Menu 221
- 2 Select either: 229
- Simulink LTI Viewer 231
- A Sample Analysis Task 231
- Model_Inputs_and_Outputs 233
- Get Line arized Mod el 239
- Linearized Model 239
- Performing Linear Analysis 243
- Saving Analysis Models 247
- 7 Control Design Tools 250
- Root Locus Design 251
- Pole Placement 253
- Optimal State-Feedback Gain 257
- Kalman State Estimator 257
- LQG Design 259
- The Root Locus Design 261
- 8 The Root Locus Design GUI 262
- A Servomechanism Example 265
- Specifying the Design Model 271
- Gain text boxon the 273
- As you get close to a closed 275
- Zoom button to zoom in 277
- Gain,andpressingthe 281
- Gain box 283
- Add Grid/Boundary menu 285
- Tools menu 285
- Edit Compensator menu item to 287
- Add compensator poles here 289
- Compensator 293
- Marker for the 295
- Then type 297
- Designating the Model Source 299
- Listing Poles and Zeros 301
- Show Ob ject buttons in this 303
- OK to close this window 303
- The plant, P (Gservo) 305
- The root locus 305
- Sensor dynamics, H 305
- Pre-filter, F 305
- 9 Design Case Studies 310
- H = zpk(0,–0.333,1); 323
- D = zpk(0.85,0,1,Ts) 333
- LQG Regulation 339
- Cross-Coupling Between Axes 351
- MIMO LQG Design 355
- Steady-State Design 359
- Kalman Filtering 361
- Time-Varying Kalman Filter 365
- 10 Reliable Computations 374
- Choice of LTI Model 381
- 11 Reference 392
- Category Tables 393
- 11append 402
- Example The commands 403
- Feedback connection 404
- Parallel connection 404
- Series connection 404
- Syntax asys = augstate(sys) 405
- Syntax sysb = balreal(sys) 406
- Phase (deg); Magnitude (dB) 407
- Algorithm Consider the model 408
- Syntax bode(sys) 409
- Syntax sysd = c2d(sys,Ts) 414
- Example Consider the system 414
- Modal Form 417
- Companion Form 417
- Examples Example 1 420
- Example 2 421
- Example w = logspace(1,2,2); 423
- 11connect 424
- Center, 1976 429
- Syntax [P,Q] = covar(sys,W) 430
- Syntax Co = ctrb(A,B) 433
- Syntax sysc = d2c(sysd) 438
- Syntax sys1 = d2d(sys,Ts) 441
- Syntax [Wn,Z] = damp(sys) 442
- 1746–1754 446
- 11dcgain 447
- Syntax sys = delay2z(sys) 448
- Syntax X = dlyap(A,Q) 451
- Syntax sys = drss(n) 452
- Syntax sys = dss(a,b,c,d,e) 455
- Example The command 456
- 11dssdata 457
- Syntax s = esort(p) 458
- , sort Sort system poles 459
- Compute system poles 459
- Pole-zero map 459
- Compute (transmission) zeros 459
- Syntax est = estim(sys,L) 460
- 11evalfr 462
- 11feedback 463
- Example 3 466
- Syntax sys = filt(num,den) 467
- Example Typing the commands 468
- Example Type the commands 470
- Create transfer functions 471
- Create zero-pole-gain models 471
- Set model properties 473
- 11freqresp 474
- 11gensig 477
- Plot the resulting signal 478
- Syntax hasdelay(sys) 483
- Syntax impulse(sys) 484
- Amplitude 486
- Syntax initial(sys,x0) 488
- Purpose Invert LTI systems 491
- Syntax isys = inv(sys) 491
- Example Consider 491
- Syntax boo = isct(sys) 494
- Syntax boo = isempty(sys) 495
- Example Both commands 495
- Syntax boo = isproper(sys) 496
- Syntax boo = issiso(sys) 497
- Continuous-Time Estimation 498
- Discrete-Time Estimation 499
- Syntax sys = lft(sys1,sys2) 505
- Syntax rlqg = lqgreg(kest,k) 507
- Syntax [K,S,e] = lqr(A,B,Q,R) 511
- Form LQG regulator 512
- Syntax lsim(sys,u,t) 516
- Then simulate with lsim 518
- Syntax ltiview 523
- See Also bode Bode response 524
- 11margin 527
- MATLAB responds with 528
- Syntax sysr = minreal(sys) 530
- M odel order reduction 531
- Structured model reduction 531
- Purpose Model order reduction 532
- Syntax n = ndims(sys) 536
- Example sys = rss(3,1,1,3); 536
- Syntax ngrid 537
- Open−Loop Gain (dB) 538
- Syntax nichols(sys) 539
- See Also bode Bode plot 545
- Syntax nyquist(sys) 546
- Syntax Ob = obsv(A,B) 549
- Example Determine if the pair 549
- Syntax [A,B,C,D] = ord2(wn,z) 553
- Syntax [num,den] = pade(T,N) 554
- N>10 should be avoided 556
- 11parallel 558
- Purpose Pole placement design 560
- Syntax K = place(A,B,p) 560
- Syntax pzmap(sys) 563
- Imag Axis 564
- Syntax rsys = reg(sys,K,L) 566
- Example sys = rss(4,1,1,2,3); 569
- 11rlocfind 570
- Purpose Evans root locus 572
- Syntax rlocus(sys) 572
- Syntax rltool 575
- F and H 578
- Syntax sys = rss(n) 579
- 11series 581
- Property 584
- Syntax sgrid 590
- Syntax sigma(sys) 592
- Nichols plot 596
- Nyquist plot 596
- Syntax size(sys) 597
- Test if LTI model is empty 598
- Test if LTI model is SISO 598
- Syntax msys = sminreal(sys) 599
- Syntax sys = ss(a,b,c,d) 601
- Conversion to State Space 602
- Syntax sysT = ss2ss(sys,T) 605
- Syntax [sysb,T] = ssbal(sys) 606
- 11ssdata 608
- Syntax step(sys) 610
- Syntax sys = tf(num,den) 614
- Example 4 618
- Discrete-Time 618
- Conventions 618
- 11tfdata 621
- Specify transfer functions 623
- Syntax td = totaldelay(sys) 624
- Syntax zgrid 626
- Syntax sys = zpk(z,p,k) 628
- Variable 630
- Selection 630
- Example Example 1 631
- Syntax [z,p,k] = zpkdata(sys) 633
- Get properties of LTI models 635
- Specify zero-pole-gain models 635
- See state-space models 638
- See also LTI models 639
- See transposition 639
- See Kalman estimator 639
- See time response 639
- See I/O groups 640
- See also InputName 640
- See also Simulink LTI Viewer 641
- See delays 641
- See model building 641
- See delay 641
- See frequency response 642
- See also operations 642
- See LTI properties 642
- See Simulink LTI Viewer 643
- See LTI objects 644
- See also OutputName 644
- See transfer functions 647
- See zeros 648
- See zero 648
- See also noise 648
Manuais e produtos relacionados com não MATLAB CONTROL SYSTEM TOOLBOX 9
não MATLAB EMBEDDED IDE LINK 4 Manual do Utilizador
(21 páginas)
(21 páginas)
não MATLAB SIMULINK HDL CODER 1 Manual do Utilizador
(46 páginas)
(46 páginas)
não MATLAB SIMPOWERSYSTEMS 5 Manual do Utilizador
(20 páginas)
(20 páginas)
não MATLAB XPC TARGET 4 - IO Manual do Utilizador
(52 páginas)
(52 páginas)
não MATLAB BUILDER NE RELEASE NOTES Especificações
(14 páginas)
(14 páginas)
não MATLAB COMPILER 4 Manual do Utilizador
(21 páginas)
(21 páginas)
não MATLAB TARGET SUPPORT PACKAGE 4 - FOR USE WITH TEXAS INSTRUMENTS C6000 Guia do Utilizador
(40 páginas)
(40 páginas)
não MATLAB XPC TARGET 4 - IO Guia do Utilizador
(182 páginas)
(182 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais